Home > Allen Bradley > Allen Bradley Kinetix 6000 Error Codes

Allen Bradley Kinetix 6000 Error Codes

Contents

Yaskawa America 85,265 views 14:01 How Servo Motors work: Closed Loop Training - Duration: 10:46. Loading... If the system was modified recently, has anyone tried a re-tune of the servo loop? I stopped following it after a while. http://lanprolab.net/allen-bradley/allen-bradley-kinetix-300-error-codes.php

Add to Want to watch this again later? Your cache administrator is webmaster. Transcript The interactive transcript could not be loaded. roge50June 3rd, 2014, 09:02 PMWe've been having the exact same problem. http://www.plctalk.net/qanda/archive/index.php/t-20480.html

Allen Bradley Kinetix 6000 Manual

It is that spark that makes the noise on the encoder, we cut the cord so it's inside the rubber and it fixed the problem. Your cache administrator is webmaster. Regards /Janne Share this post Link to post Share on other sites Janne 1 Hi, I am New!

The system returned: (22) Invalid argument The remote host or network may be down. The system returned: (22) Invalid argument The remote host or network may be down. The thing we don't know is if the process is building up a super sharge that can be a bigger problem, but so far are everything looking good. Allen Bradley Kinetix 6500 Working...

Edited 13 Jun 2012 by Janne Share this post Link to post Share on other sites bouws 1 Sparky MrPLC Member 1 14 posts United States Posted 21 Jan 2013 Allen Bradley Kinetix 6000 E19 About Press Copyright Creators Advertise Developers +YouTube Terms Privacy Policy & Safety Send feedback Try something new! BOTTOMLINE, when the servo gives a NOISE FAULT it can be related to mechanical!

Working...

Your cache administrator is webmaster. Allen Bradley Kinetix 5500 Generated Fri, 30 Sep 2016 04:34:16 GMT by s_hv987 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.7/ Connection The drive will drive up to the torque limit and hold there if there is no position command to trip the position error (actual vs. CleanerFebruary 7th, 2006, 11:29 AMYou would definitely see E19 if you have a mechanical bind.

Allen Bradley Kinetix 6000 E19

Please try the request again. We paid an AB expert $6000 and still unresolved. Allen Bradley Kinetix 6000 Manual If there is not enough position error to trip the fault, the drive will continue to pull torque at the limit until some other fault occurs. Allen Bradley Kinetix 350 Fault Codes We are driving a heavy load on a beltdrive actuator (yuck), through undersized cheap jaw type couplings without keys (ugh), through a 25:1 gearbox (added backlash), through another cheap jaw type

MrPLC Member 1 3 posts Sweden Posted 21 Mar 2012 (edited) This may sound strange but it fixed our problem, we discovered that when using a timing belt is the motor this contact form Thanks. I was seeing about 10 degrees of slop at the beltdrive pulley end. We have ordered a new type of belts without any cord inside and will test it later on. Allen Bradley Kinetix 2000

We do still have a few machines out there with the older motors that experience the issue so the motor shaft ground strap sounds like a good idea. Sign in here. Can it be because they have the torque O/L limit set too high in the PLC limits? http://lanprolab.net/allen-bradley/allen-bradley-slc-error-codes.php Typically if your position error accumulates over time, it may be more indicative of tuning than a bind, unless your bind was along the entire length of rotation (or stroke).

The system returned: (22) Invalid argument The remote host or network may be down. Allen Bradley Kinetix 300 Category Science & Technology License Standard YouTube License Show more Show less Loading... They've reviewed my installation and confirmed that I've gone above and beyond all the recommendations for reducing noise on the feedback cables.

Your cache administrator is webmaster.

It's only on one axis in the system. Your cache administrator is webmaster. Please try the request again. Allen Bradley Kinetix 300 E39 Fault In the past have we have this two gear belts really tight and really loose with no visible effect on the motion system.

netriderpor 544 views 1:59 102 videos Play all Popular Videos - Allen-Bradley & Rockwell AutomationAllen-Bradley - Topic RS5K-1 RSLogix5000 Quick Start - CompactLogix.mp4 - Duration: 34:29. Sign in to add this to Watch Later Add to Loading playlists... Automation Engineer 2,266 views 6:09 Galco Repairs: Allen Bradley Kinetix 6000 Servo Drive - Duration: 1:34. Check This Out GalcoTV 14,713 views 3:18 PROFINET Intro - Duration: 4:08.

GalcoTV 618 views 1:34 Servo Motor Repair And Testing Procedures - Global Electronic Services - Duration: 6:27. commanded). We ran a few sets of rails today but we keep getting this error.. It seems that 2 to 3 months after we have line upgrades to this type of system that we start getting E19 errors.

I am struggling with the E64 problem in our Kinetix 6000 system as well; I have worked with this type of system from late 2004. at this point I'm thinking it's mechanical in nature. Loading... kdcuiJuly 2nd, 2013, 12:52 PMCould be mechanical bind like Cleaner said.

Ruslan Kasymov 2,275 views 3:43 CompactLogix 5370 Controllers and Kinetix 350 Motion Drives - Duration: 41:03. Autoplay When autoplay is enabled, a suggested video will automatically play next. AdvancedMotionCont 1,005 views 6:13 Let's Play Automation : Episode 39 "Cone's 240sx" - Duration: 28:21. Generated Fri, 30 Sep 2016 04:34:16 GMT by s_hv987 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.6/ Connection

Think some system resonance or excessive slopiness is causing what looks like to the encoder to be "noise". Just an FYI and for others. What sort of move profile are you doing indexing or is it only a speed profile? Sign In Now Sign in to follow this Followers 0 Go To Topic Listing Allen Bradley All Activity Home PLCs and Supporting Devices Allen Bradley Kinetix 6000 E64 E07 faults Contact

Jim Fillmore Share this post Link to post Share on other sites James Fillmore 0 Sparky MrPLC Member 0 20 posts United States Posted 30 Jan 2012 (edited) Just got Sign in 2 0 Don't like this video?