Home > Allen Bradley > Allen Bradley Ultra 3000 Error Code E24

Allen Bradley Ultra 3000 Error Code E24

Contents

Testing and Tuning Your Axis. . . . . . . . . . . . . . . . . . . Publication 2098-IN005C-EN-P — March 2008 14 Commissioning Your Ultra3000 Drive Use this figure to locate the front panel connections on the Ultra3000 460V drives (3 W, 5 kW, 10 kW, 15 Close the Digital Inputs properties dialog. The drive is software disabled and the toolbar Enable icon is no longer on. 9. Source

Double-click the Ultra3000 icon (Ultra3k) under the On-Line Drives tree. Find More Posts by curlyandshemp March 23rd, 2009, 10:47 AM #3 OZEE Member Join Date: Mar 2006 Location: Kansas Posts: 1,695 We have been battling an Ultra3k with lots The Monitor Status dialog closes and the setup changes take affect. 16. Expand the Operation Modes parameter. http://www.plctalk.net/qanda/showthread.php?t=46004

Allen Bradley Ultra 3000 Error Code E19

Information on configuring and troubleshooting your ControlLogix and CompactLogix SERCOS interface modules. Verify the Drive Enabled lamp is ON (yellow) c. Using this table, determine the sequence of these three inputs that correspond to the preset gear ratios entered. After talking with AB techconnnect they had us check cable continuity and after plugging the cable back in the drive has ran for through the weekend continuosly with a test program.

monitoring the oscilloscope as it traces the selected drive signal. Click OK. 10. Before handling the equipment, voltages should be measured to determine safe levels. Allen Bradley Ultra 3000 Manual The Digital Output properties dialog opens. 7.

In this example both Drive Enable and Fault Reset are combined in Input 1. Allen Bradley Ultra 3000 Fault Codes Status Logic Power If the Logic Power status indicator is ON Not ON Then Go to step 3. 1. Refer to the Ultraware User Manual, publication 2098-UM001, for more information on absolute indexing moves. read this article The drive is software disabled and the enable icon in the toolbar is no longer illuminated.

In the Explorer dialog, right-click an axis and choose Properties. Allen Bradley Ultra 3000 User Manual Description The instructions needed for the installation and wiring of the Ultra3000 drives. It's not a question of parameter or anything like that because i've been testing the drive during the production all day( making it make long fast stroke whenever the system need Default interpolation is x256 which totals 1024 x 256 or 262,144 counts per revolution.

Allen Bradley Ultra 3000 Fault Codes

The Monitor Status dialog closes. 11. Verify the Drive Enabled lamp is ON (yellow) c. Allen Bradley Ultra 3000 Error Code E19 Observe the Status table. • • Drive Enable status = lamp is on (yellow) Velocity - Motor Feedback status = the value you entered in step 5 8. Allen Bradley Ultra 3000 Software IMPORTANT If you do not have an Ultra3000X indexing drive, you cannot access the indexing functions.

Notice that the auxiliary encoder uses Preset 1 as the Gear Ratio or 2:1. http://lanprolab.net/allen-bradley/allen-bradley-ultra-3000-error-code-e30.php Apply Power to Your Ultra3000 Drive with SERCOS. . . In the Name box, enter your module name b. Publication 2098-IN005C-EN-P — March 2008 58 Commissioning Your Ultra3000 Drive Configure Axis Properties Follow these steps to configure axis properties. 1. Allen Bradley Ultra 3000 I Drive

Publication 2098-IN005C-EN-P — March 2008 52 Commissioning Your Ultra3000 Drive Configuring Your Ultra3000 Drive with RSLogix 5000 Software In this section you will configure your Ultra3000 drive by using Ultraware software, Sign in here. The drive is faulted. http://lanprolab.net/allen-bradley/allen-bradley-ultra-3000-error-code.php Expand the Operation Modes parameter and verify the Operation Mode is Analog Velocity Input.

Apply Power to Your Ultra3000 Drive with DeviceNet . . . 10 . . . . . . . . . . . . . . . . . . . Allen Bradley Ultra 3000 Servo Drive or it can go in error every 1 hour. Scanner Problems . . . . . . . . . . . . . . . . . . . . .

The Motion Group Properties dialog opens. 5.

Select Drive Fault Input - Normally Closed. 3. The drive properties dialog opens. 2. Observe that Velocity - Command matches what was entered in Preset Velocity 0. 18. Allen Bradley Ultra3000 Error Code E19 The Ultra3000 Drive properties dialog opens.

To display velocity in rpm divide 8000 counts/rev by 60 seconds/ minute or 133.333. For position and acceleration use 8000. Close the Digital Outputs dialog. 4. Check This Out Setting Position Error Limits in Ultraware and RSLogix 5000 Software . . . . . . . . . . . . . . . . . . . . .

Your new module appears under the I/O Configuration folder in the Explorer dialog and the Module Properties dialog opens.