Home > An Unknown > An Unknown Error Occured 2131

An Unknown Error Occured 2131

Also, when the driver's attempt to HALT the core fails, it checks to see whether it is due to memory-hang condition. Content is available under Creative Commons Attribution-ShareAlike unless otherwise noted. Similarly as above, a bus may be hung range from either an invalid instruction that can misconfigure the memory interface; a bus locked by another core, a peripheral or DMA (bus A generic error is shown at: Lost control of device execution state For MSP432 check the remark at: Invalid device ID For Wireless connectivity devices, check this e2e forum thread For have a peek at these guys

Device register This error means the JTAG debugger is unable to access the core or device on the board. The user must turn-on or connect the power supply for the target. Restart the computer. All Rights Reserved. https://discussions.apple.com/thread/1144796?tstart=0

iLounge is © 2001 - 2016 iLounge, Inc. Check their pages at XDS560 and XDS560v2 System Trace. This is mostly applicable to XDS110 and XDS200. If error persists, confirm configuration, power-cycle the board, and/or try more reliable JTAG settings (e.g.

thanks. so in response, a new driver might not help. If the data read back is all zeros (0x00000000), it is possible there is a power failure on the circuit or one of the JTAG lines has a short to GND. If the issue happens during connect phase, check the Troubleshooting the connect phase section below.

Confirm device and emulator configuration is correct, or update device driver. C28xx: Error connecting to the target: (Error -1135 @ 0x0) The debug probe reported an error. The title is 'SC_ERR_OCS_PORT'. http://unknown.error.occurred.2131.itunes.winwizards.org/ And if i do have to reburn the cd, what software should i use.

Register Now! Netbooks do not have a CD, DVD or Blu-ray drive built in. XDS100: An error occurred while soft opening the controller. -----[An error has occurred and this utility has aborted]-------------------- This error is generated by TI's USCIF driver or utilities. Date Updated: 12/04/2013 Can my optical drive burn a DVD?

If error persists, confirm configuration, power-cycle the board, and/or try more reliable JTAG settings (e.g. http://unknown.error.occured.2131.winwizards.org/ Correct the target configuration file. Any help would be greatly appreciated! 08-19-2007, 12:23 PM #2 cjmnews Join Date: Apr 2006 Location: Arizona Posts: 8,181 permalink Apple will ask you to try different discs. Test 3 Word 5: scanned out 0xFE03E0E2 and scanned in 0x80F838BF.

Note: This article was updated on 2016-09-24 and previously published under WIKI_Q210794 Contents 1.What is Unknown Error Occured 2131 error? 2.What causes Unknown Error Occured 2131 error? 3.How to easily fix More about the author Error connecting to the target: (Error -1060 @ 0x0) Device is not responding to the request. I am wasting cd's each time I try to burn from itunes because it does initialize the disc. This Unknown Error Occured 2131 error code has a numeric error number and a technical description.

To verify this you can check the steps shown in the Firmware update section for XDS110 and XDS200. Choose 'Rude Retry' to disable polite mode and force the operation. How does it work? check my blog FTDI driver function error This error happens whenever the JTAG scan manager software has sent a command to the FTDI chip in the XDS100, and the FTDI driver returned either an

This test will be applied just once. The utility or debugger has requested that a target device be repeatedly accessed for a specific data or status value. My computer is a Dell Inspiron 1501.

In some cases the error may have more parameters in Unknown Error Occured 2131 format .This additional hexadecimal code are the address of the memory locations where the instruction(s) was loaded

However, if there is a more severe power outage on the device, the JTAG debugger is unable to bring it out of this mode: Error: (Error -1155 @ 0x0) Device may While the software CD that ships with the monitor indicates that the Acer PhotoFit... If error persists, confirm configuration, power-cycle the board, and/or try more reliable JTAG settings (e.g. Instructions To Fix (Unknown Error Occurred 2131 Itunes) error you need to follow the steps below: Step 1: Download (Unknown Error Occurred 2131 Itunes) Repair Tool Step 2:

A very rare error is shown below: Generic FTDI failure 8. They are designed to install software and watch videos downloaded from the internet instead of from an optical drive. PLEASE anyone that can help I would appreciate it sooooooooo very much!!!! news Test 3 Word 1: scanned out 0xFE03E0E2 and scanned in 0xFC07C1C5.

The short clips Launching a project target configuration manually or Launching a shared target configuration manually at the Quick Tips page. put in your service tag (bottom of your laptop)3. It happened on drive D: SONY CDRWDVD CRX880A on CDR media at speed 24X. Get Support Drivers and Manuals Acer Community Chat My Acer Search Search Answers US/CAN English [?] Search Results Recommended Links Prev 1 2 3 4 Next Other Suggested Searches battery light

Date Updated: 02/04/2014 Prev 1 2 3 4 Next Filters All Products Select your model Related Community Discussions Re: Is it possible to get ubuntu to work G9-591 Re: Acer 5749