Home > An Unknown > An Unknown Error Occurred 2131

An Unknown Error Occurred 2131

IcePick_C: Error connecting to the target: (Error -275 @ 0x0) The attempt to poll a target device exceeded its timeout limit. Test 3 Word 3: scanned out 0xFE03E0E2 and scanned in 0xFC07C1C5. I talked to dell, and i got a new drive. Apple disclaims any and all liability for the acts, omissions and conduct of any third parties in connection with or related to your use of the site. have a peek at these guys

Review the Emulation FAQ 6. Does your emulator support the target I/O voltage? Device register This error means the JTAG debugger is unable to access the core or device on the board. Lost control of device execution state This error means the device is free running and the JTAG debugger lost control of its core and status.

Please type your message and try again. There are two (2) ways to fix Unknown Error Occurred 2131 Error: Advanced Computer User Solution (manual update): 1) Start your computer and log on as an administrator. 2) Click Thread Tools Show Printable Version Email this Page Display Modes Linear Mode Switch to Hybrid Mode Switch to Threaded Mode Thread Tools Show Printable Version Email this Page Display Modes Linear This test will be applied just once.

Click here follow the steps to fix Unknown Error Occurred 2131 and related errors. This tool will scan and diagnose, then repairs, your PC with patent pending technology that fix your windows operating system registry structure. put in your service tag (bottom of your laptop)3. I have tried the suggestions you have offered, and realize now that it is not a fixable issue unless I get a new driver.

If error persists, confirm configuration, power-cycle the board, and/or try more reliable JTAG settings (e.g. I put Nero onto my computer and tried burning the same contents that I had been trying to burn with iTunes and Nero wouldn't even let me finish the process. Helpful (0) Reply options Link to this post Page 1 Next This site contains user submitted content, comments and opinions and is for informational purposes only. http://unknown.error.occurred.2131.itunes.winwizards.org/ Power loss This error means the JTAG debugger is unable to sense the presence of a power supply voltage on the target - the TVRef pin.

Check the external power supply. Date Updated: 08/29/2016 Why isn't my CD or DVD drive showing up in Windows after flashing the BIOS for RAID support on my Acer Aspire 9800 notebook? How to easily fix Unknown Error Occurred 2131 error? Dead JTAG clock This error is shown when the JTAG debug probe does not receive a clock signal on the RTCK pin.

Thanks again for all of the suggestions. original site If error persists, confirm configuration, power-cycle the board, and/or try more reliable JTAG settings (e.g. The utility or debugger has requested that a target device be repeatedly accessed for a specific data or status value. How to easily fix Unknown Error Occured 2131 error?

If you have Unknown Error Occurred 2131 errors then we strongly recommend that you Download (Unknown Error Occurred 2131) Repair Tool. More about the author Unknown Error Occurred 2131 Error Codes are caused in one way or another by misconfigured system files in your windows operating system. If you are unable to connect to a specific core of an SoC device (IVAHD, EVE, IPUSS, PRUSS, etc.), you may need to release it from reset. Does anyone have any new remedies? 02-07-2009, 01:42 AM #10 StephenDest Freshman Lounger Join Date: Sep 2007 Posts: 10 permalink There is finally a new firmware for the

If the data read back is all ones (0xFFFFFFFF), it is possible that one of the JTAG lines has a short to VCC. Confirm debug probe configuration and connections, reset the debug probe, and retry the operation. The whole process takes about 5 minutes. check my blog My computer is a Dell Inspiron 1501.

Disclaimer: This website is not affiliated with Wikipedia and should not be confused with the website of Wikipedia, which can be found at Wikipedia.org. All postings and use of the content on this site are subject to the Apple Support Communities Terms of Use. This code is used by the vendor to identify the error caused.

The first time i tried to burn a cd with my new drive it gave me the same error.

All Rights Reserved. It happened on drive D: SONY CDRWDVD CRX880A on CDR media at speed 24X. The value is '-150' (0xffffff6a). Date Updated: 12/04/2013 How do I create a set of backup recovery disks?

Choose 'Rude Retry' to disable polite mode and force the operation. How does it work? Go to downloads and the CD / DVD Drives5. news Date Updated: 12/04/2013 Can my optical drive burn a DVD?

Check if the target configuration file (.ccxml) is running at a clock speed compatible with the board and device. Helpful (0) Reply options Link to this post by tangoman-uk, tangoman-uk Jan 8, 2008 9:57 AM in response to mainkis Level 1 (0 points) Jan 8, 2008 9:57 AM in response Check the Windows Control Panel or the XDS200 known issues. iPod, iPhone, iPad, iTunes, Apple TV, Mac, and the Apple logo are trademarks of Apple Inc.

Anyways, I just wanted to thank you for your response-this site seems to be an excellent resource!Lynne Helpful (0) Reply options Link to this post by apsoccer, apsoccer Nov 9, 2007 This corrupted system file will lead to the missing and wrongly linked information and files needed for the proper working of the application. McAfee released a patch to address the activation. (The patch enables 60-day trial to be used) Ensurethat your Acer Home Server is powered on and has beensetup. I am so extremely frustrated and am looking at other paid downloading sites, but am disappointed because I really wanted to use itunes, in addition to wasting 15 dollars on the

Video Display Information ATI Radeon Xpress 1150 **** External Plug-ins Information **** No external plug-ins installed. **** CD/DVD Drive Tests **** LowerFilters: PxHelp20 (2.0.0.0), UpperFilters: GEARAspiWDM (2.0.7.5), D: SONY CDRWDVD CRX880A, Do you want to bring it out of this mode? One example is a typical stuck-at-ones or stuck-at-zero fault: Error connecting to the target: (Error -233 @ 0x0) The JTAG IR and DR scan-paths cannot circulate bits, they may be broken. awesome.