Home > An Unknown > An Unknown Error Prevented The Emulator From Accessing The Processor

An Unknown Error Prevented The Emulator From Accessing The Processor

It is recommended to RESET EMULATOR. Pramod PoudelWhen I tried to connect after executing lpmOFF and lpmON( I executed this since I had already ran some application on DSP), I got following error. Trademarks | Privacy Policy | Terms of Use TI E2E Community Menu Search through millions of questions and answers User Menu Search through millions of questions and answers User TI E2E CCS (v3.0 and v3.1 or later) and Blackhawk XDS560-class emulators: Can't load DSP device driver "...\drivers\tixds560xxxx.dvr" A installation choice of CUSTOM (not FULL or TYPICAL) of CCS (v3.0 or v3.1 and have a peek at these guys

Did you read theCCS Forum Guidelines & FAQ? Blackhawk USB560 emulator sues the SAME setup as the TI XDS560 PCI emulator! Tools Insider University Program Groups Corporate Citizenship TI University Program Russian E2E (сообщество E2E) Japanese E2E (日本語コミュニティ) Learn E2E Launch Your Design Motor Drive & Control Videos More Cancel C6000 Single As the DSP by default is in reset mode, I ignored this error and started the debug session.

It is recommended to RESET EMULATOR. The USB 2.0 and USB560 JTAG Emulators support all of the devices that TI supports in Code Composer Studio (C2000, C5000, C6000, ARM and OMAP). It's very annoying, especially when combined with the other problem I am trying to figure out in which the logtrace window does NOT work on the first run of a program After going throughhttp://e2e.ti.com/support/dsp/omap_applications_processors/f/447/t/29982.aspx?PageIndex=1, I removed all the .gel files and then started "Debug Active Project" .

So, in summary, we can support all devices below, one way or another, except those marked with (x). (x)TMS320C30-32 (#)TMS320VC33 (x)TMS320C4x (x)TMS320C5x (*#)TMS320F24x (*#)TMS320F240x (*)TMS320C27x (*)TMS320F280x (*)TMS320C54x (*)TMS320C55x (*)TMS320C6000 (*)TMS320C64x (*)TMS320C67x I get "error initializing emulator" when I run CCStudio. Also try deleting the existing Debug launches for the project. You have the same POSIX system calls available to you across each TMS320 platform, so moving from one to the other is easy.

Please note that you need CCS v2.1 or later to use an XDS560-class driver, which is a requirement imposed by TI. - We can also support operation in XDS510-class mode. It is recommended to RESET EMULATOR. This old way did not take advantage of the USB interface. https://e2e.ti.com/support/dsp/tms320c6000_high_performance_dsps/f/112/t/11550 Urget help is required.

I have just installed one of your USB560 emulators. I am using OMAP Code Composer v2.2 with the USB560 JTAG emulator. What versions of Code Composer & Code Composer Studio do you support? The targets should then be power cycled or hard reset followed by an emureset and reconnect to each target.

All Rights Reserved. read review Supported by our USB 2.0 and USB560 JTAG Emulators. Valid controller handles are generated when attempts to open the controller return a clean error status. Yes.

First, select the "Register Now" link on the login box. http://lanprolab.net/an-unknown/an-unknown-error-occurred-while-accessing-flash.php Will Blackhawk emulators work with CCS2.20 Eval version? Some of XDS560 features include HS RTDX and faster code download. These are listed below with the prefix (*).

I did have other options but this looked better choice as I am working on Beagleboard Those are the files I used also. The idea here is to program the flash with code to put it into an infinite loop allowing CCS to halt each core and start up. Tools Insider University Program Groups Corporate Citizenship TI University Program Russian E2E (сообщество E2E) Japanese E2E (日本語コミュニティ) Learn E2E Launch Your Design Motor Drive & Control Videos More Cancel C6000 Single check my blog This will disconnect each target from the emulator.

Does USB560 support CCS 2.2 with OMAP or DM270 processors? Yes. I have attached my main code below: 1538.FIR3LP.c Thank you!

This will disconnect >>each target from the emulator.

TI has two different classes of emulators, which are referred to by XDS510 and XDS560 classes. If this does not resolve the issue, please contact Blackhawk support at this link: http://www.blackhawk-dsp.com/SupportRequest.aspx CCS v3.2 - I updated to CCS v3.2.39.5 and can no longer connect to my C64x+ If you haven't read it in awhile, please read it again to see if any updates were made. At the next screen choose the "Regular User" role.

Could this be a software issue with Code Composer or the emulator? No license, either express or implied, by estoppel or otherwise, is granted by TI. Innovate with 100,000+ analog ICs andembedded processors, along with software, tools and the industry’s largest sales/support staff. © Copyright 1995-2016 Texas Instruments Incorporated. news A bad DMA sequence or pointer are examples.

Register Remember Me? I remember from our XDS 510, there was something unusual about the JTAG clock with the OMAP. I did not have any other option for .gel file for DSP. If not, PLEASE read it.

Then I press stop, soft-reset the board and recompile and reload the program. The new version of silicon for the 5510 requires that an 8-bit bypass be configured in Code Composer. This is located under key, HKEY_LOCAL_MACHINE\SOFTWARE\GODSP. TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these

SEO by vBSEO ©2011, Crawlability, Inc. --[[ ]]-- Sign in Register Home Projects Help Search: Mity CPU Platforms » TI TMS320C6xxx Based Products Overview Activity News Wiki Forums Forums » Software Reason: Failed to load program 'cvDFT.out' on any of the targets. What do you mean by “operates in XDS510-mode”? It is recommended that you reset the emulator before you connect and reload your program before you continue debugging.

Do your high-speed USB 2.0 emulators support USB 1.1? The targets should then be power cycled or hard reset followed by an emureset and reconnect to each target. Innovate TI Live @... Urget help is required.

Electrical & Computer Engineering >Greece > > > > > > _____________________________________Posted by Michael Dunn ●January 29, 2009tkc, On Thu, Jan 29, 2009 at 12:42 PM, wrote:> > Hi, > Even I also deleted all the Debug lunches for all the projects. Does anyone know what would the error below mean? > >>CPU_1-DSP Device Driver >> >>Trouble Halting Target CPU: >>Error 0x80000020/-1070 >>Fatal Error Execution. >>An unknown error prevented the emulator from accessing In order to gain access to the driver download areas, you must register with this site.