Home > Error Code > Amana F-3 Error

Amana F-3 Error

Contents

Part number: AP88013 Good Luck, __________________ Thanks for allowing AppliancePartsPros.com to assist you, Joe M. F1-A - Circuit Board Grounding - Replace control board (clock). You did disconnect the sensor at the wire nuts, or plastic connector and check the resistance on the wires/pins ? Related ModelsAmanaAGS781WWRANGE- S/C S/I DDRAFT GASAmanaAGS781WWRANGE- S/C S/I DDRAFT GASAmanaAGS781WWRANGE- S/C S/I DDRAFT GASGeneral ElectricAGT05LBG1Room air conditionerGeneral ElectricAGT05LHG1Room air conditionerFrigidaireAGTL175WH1-57Tap(v7) / Top Mount RefrigeratorFrigidaireAGTN175WH1-57Tap(v2) / Top Mount RefrigeratorGeneral ElectricAGV05LBG1Room air conditionerGeneral Check This Out

Electric Range - Bisque See Details Related Pages Appliances 156K followers Follow Ranges 614 followers Follow Sweeps Personal Shopper Gift Registry Legal & Privacy | Help | Feedback Login|Contact Us Appliance If it is defective it will need to be replaced, it is not possible to repair the sensor. See below for a detailed temperature/resistance chart. The measurements repeat all time. http://www.partselect.com/JustForFun/Amana-Appliance-Fault-Codes.aspx

Amana Stove Error Codes

I apreciate for all !!!! In this case finding where the sensor circuit wires attach to the electronic control will be necessary to perform testing at that point. Question about Whirlpool Kitchen Ranges 1 Answer F2 &F3 error codes, oven keeps beeping, I ...F3 error codes, oven keeps beeping, I already tried turning off circuit breaker did not solve

thanks for your assistance Expert: Tim Alan replied4 years ago. by Manage My Life December 4th, 2008 Comment Give your feedback by voting on answers 0 votes Didn't find what you are looking for? On a built in oven, that may involved removing the appliance from its enclosure. Amana Oven F9 Error Researched code F3 indicates Open or Short Temperature sensor.

Ask Tim Alan Your Own Question Tim Alan, Home Appliance Technician Category: Appliance Satisfied Customers: 1256 Experience: Amana, A&E (Whirlpool) ,and Maytag factory service 51145682 Type Your Appliance Question Here... Amana Washer Error Codes Question about Maytag Kitchen Ranges 2 Answers F3 error code F3 error code What is the F3 error code. I would check the temperature sensor fist and the wiring all the way from the sensor to the oven control. Your sensor is working backwards, based on your information.

Amana Dual Convection Wall Oven Fault Codes Note: Depending upon the brand of appliance, there can be many different names for the 'clock' component. Amana Furnace Error Codes Top 4 Reasons Gas Burner Won’t Light? Researched code F3 indicates Open or ..." User Name Remember Me? F7 - Shorted or Stuck Button - Check glass alignment and replace touch pad if necessary.

Amana Washer Error Codes

If these two tests measure the same, it would usually indicate the wiring harness is not the problem leaving the sensor as the most likely culprit. his comment is here Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.

LinkBack LinkBack URL About LinkBacks Bookmark & Share Digg this Thread! Amana Stove Error Codes Error Message ~ Only While in Use ~ If the error message (or an erroneous temperature display) only occurs during use, it would be dangerous to attempt to remove the sensor Amana Oven F1 Error Code F3 - E0, Oventemperature ...

Question about KitchenAid Kitchen Ranges 1 Answer Gives codes F-2 &F3 what Error Code F3 F3 error codes are triggered by problems with the oven temperature sensor. his comment is here ft. It always had some 9/30/2016 9/30/2016 Tyler Z. JustAnswer.com...has seen a spike since October in legal questions from readers about layoffs, unemployment and severance. Amana Oven Temperature Sensor

The f3 is an open or shorted oven sensor an f2 is an oven temperature too hot or a runaway temp. We can repair most timers so if you are sure your problem pertains to the timer (or ERC) please fill out a repair service request and send us your timer to F1-J - Latch Switch Input Circuit Failure - Check Door Switch and Wiring. this contact form How do I check an oven temperature sensor?

Replace control board if failed. Amana Range Error Code F9e0 They truly know what they are talking about, and they actually care about you. There should be a plastic terminal block on the wires which may have to be manipulated to get it through the hole in the rear of the oven cavity.

Justin Kernersville, NC Just let me say that this encounter has been entirely professional and most helpful.

Check the range's wiring diagram for that possibility. Submitted: 4 years ago. I find it hard to believe that the sensor could be bad but it is possible. Amana Dryer Error Codes Top 4 Reasons Gas Oven Won’t Bake Evenly?

See Details Kenmore 94184 5.4 cu. disclaimer and Terms of Use. Do you have the same question?Follow this Question InHome>Appliance Repair Report It Tweet 1 Answer 0 Votes Edit Answer (for another -33 minute) The F3 code indicates a defective temperature http://lanprolab.net/error-code/amana-error-code-f3.php Sometimes, even when the failure code implies that another component has failed this can actually be a timer problem (whereby the timer is not displaying the correct fault code).

If oven temperature sensor is ok, replace control board (clock). Appliance Doc Satisfied Customers: 72478 9+ years being an appliance technician with factory training. Question about Jenn-Air Kitchen Ranges 1 Answer F3 error code f3 error code I REPLACED THE OVEN SENSOR AND STILL RECIEVING F3 ERROR CODE AND THE COOLING FAN IS RUNNING Check disclaimer and Terms of Use.

The measurements repeat all time. Replace if faulty. Forum Forum Home New Posts FAQ Calendar Community Albums Member List Forum Actions Mark Forums Read Quick Links Today's Posts Appliance PartsAppliance Maintenance TipsApplianceBlog Home Advanced Search Forum Appliance Repair Talk